Kim BS F19 and ISO are alternative names for the same method which is intended to measure the resistance of coatings to a defined cycle of UV radiation and salt spray. The size and shape of the cabinet shall be such that the collection rate of solution in the cabinet is within the limits specified in Table? Unless otherwise specified, the cut edges shall be adequately protected by coating them with a suitable material, stable under the conditions of dij test, such as paint, wax or adhesive tape. After each stripping, thoroughly clean the reference specimens at ambient temperature with water, then with ethanol, followed by drying.
|Published (Last):||24 September 2010|
|PDF File Size:||16.4 Mb|
|ePub File Size:||3.73 Mb|
|Price:||Free* [*Free Regsitration Required]|
Gardakasa For this purpose, a dispersion tower equipped with an atomizer may also be helpful. If dih coating on the back or edges of the panel differs from that of the coating product under test, it shall have a corrosion resistance greater than that of the coating product under test. Unless otherwise specified, the back and edges of the panel shall be coated with the coating system under test.
These tests are designed to evaluate how well the surface coatings protect substrates from corrosion. The method differs from the standard di spray tests in that the salt solution used in the prohesion test is much more dilute and the panels are not exposed to it continuously.
In addition, for quality control purposes, comparison can be made between specimens coated with the same coating. Chromaflo Technologies opens new manufacturing facility in India 30th March Read more. They are not intended to be used for comparative testing, to rank different materials relative to each other with respect to corrosion resistance.
Sika acquires Austrian manufacturer of waterproofing systems 19th January Read more. This is a matter of agreement between the parties concerned. Weigh the reference specimens to the nearest 1 mg. If specified, make a straight scratch or scribe mark through the coating to the substrate. ISO — Paints and varnishes — Determination of resistance to neutral salt spray fog One or two scribe marks may be applied.
Photographic records of the tested specimens may, if required, accompany the report. Resistance to Cyclic Prohesion. After this procedure, the specimens to be tested are placed in the cabinet. The average rate of collection of solution in each device shall be measured over a minimum period of 24 h of continuous spraying. Isoo to Salt Spray. Assessment of degree of cracking ISO? After it has been confirmed that the test conditions are within a specified range, izo spraying the salt solution, fill the test chamber with test specimens and start the test.
The recommended test duration is: The test duration shall be 24? The test duration shall be 48 h. Weigh the reference specimen to the nearest 1? Toby Padfield — Troy, Michigan. The pressure should be 98? The salt spray tests are particularly useful for detecting discontinuities, such as pores and other defects in certain metallic, organic, anodic oxide and conversion coatings.
It also describes the method employed to evaluate the corrosivity of the test-cabinet environment. Divide the determined mass loss by the area of the exposed surface area of the reference specimen, to assess the metal mass loss per square metre of the reference specimen.
Before testing, the reference specimens shall be cleaned carefully with a hydrocarbon solvent, in order to remove all evidence of dirt, oil, or other foreign matter capable of influencing the result from the corrosion-rate determination.
Welcome to new Member Olin Epoxy! We can test different size samples if required with maximum dimensions of x x mm. Sample Requirements Ideally x 75 mm coated burnished steel panels not more that 5 mm thick, although we can accommodate a limited number of x mm panels provided they are less than 5 mm thick. Tikkurila finalises first quarter of with revenue growth 4th May Read more. The prohesion test is a less severe version of the standard salt spray tests and is generally regarded as giving a better correlation with outdoor exposure results.
Chemture shareholders approve acquisition by Lanxess 8th February Read more. It is recommended that freshly prepared vin be used during each procedure for the removal of corrosion products. The test duration is 24? The level of the salt solution in the salt reservoir shall be maintained automatically to ensure uniform spray delivery throughout the test. As comparative tests, however, salt spray tests are only suitable if the coatings are sufficiently similar in nature.
After each stripping, thoroughly clean the reference specimens at ambient temperature with water, then with ethanol, followed by drying. For chemical cleaning, use a solution with a mass fraction of 20? Nevertheless, the method described gives a means of checking that the comparative quality of a metallic material, with or without corrosion een, is maintained.
Assessment of degree of rusting DIN EN ISOPaints and varnishes — Evaluation of degradation of coatings — Designation iao quantity and size of defects, and of intensity of uniform changes in appearance — Part 4: In order to obtain a total test area of 0. We will be pleased to advise you regarding our requirements.
Nevertheless, the method described gives a means of checking that the comparative quality of a metallic material, with or without corrosion protection, is maintained. It also describes the method employed to evaluate the corrosivity of the test? Remove the corrosion products by mechanical and chemical cleaning as described in ISO?
An ultrasonic bath may preferably be used for increasing the rate of dissolution. Protect one face of the reference specimens with a removable coating, for example an adhesive sin film.
The support for the reference specimens shall be made of, or coated with, inert materials such as plastics. Related Posts
DIN EN ISO 7235:2010-01
Kazrall Resistance to Cyclic Salt Spray. Test specimens of types different from the reference specimens shall not be placed in the test chamber during the verification procedure. The salt spray methods are all suitable for checking that the comparative quality of a metallic dinn, with or without corrosion protection, is maintained. One or two scribe marks may be applied.
DIN EN ISO 7253:2002-04
DIN EN ISO 9227:2006-10
DIN ISO 7253:1998-09 - Entwurf