Mesho If you install two hard disks on motherboars, you must configure the second drive to Slave mode by setting its jumper. Page 88 Using 4- or 6-Channel Audio Function Connecting the Speakers When you have set the Multi-Channel Audio Function mode properly in the software utility, connect your speakers to the correct phonejacks in accordance with the setting in software utility. Avoid clearing the CMOS while the system is on; it will damage the mainboard. Power Power Speaker Switch Setting options are described below.
|Published (Last):||18 September 2006|
|PDF File Size:||14.1 Mb|
|ePub File Size:||15.12 Mb|
|Price:||Free* [*Free Regsitration Required]|
Mezibar Any changes made to this setting may cause a stability issue, so changing the DDR voltage for long-term purpose is NOT recommended. Make sure to raise the lever up to a degree angle. The S-Bracket offers 2 SPDIF jacks for digital audio transmission one for optical fiber connection and the other for coaxialand 2 mothrboard Line-Out jacks for 4-channel audio output.
Page 80 Using 4- or 6-Channel Audio Function 3. To enable 4- or 6-channel audio operation, first connect 4 or 6 speakers to the appropriate audio connectors, and then select 4- or 6- channel audio setting in the software utility. Floppy The system will boot from floppy drive. Page of Go. Mottherboard 92 Using 4- or 6-Channel Audio Function 4. Hardware Setup Central Processing Unit: A logical block address is a bit value ot4av maps to a specific cylinder-head-sector address on the disk.
Some commonly-used audio output for- mats midi, wav. Selecting the First Boot Device Use of high performance defaults will tighten most timings to increase the system performance.
Installing The Audio Driver 1. The setup maual will automatically appear. Alternatively, please try the following help resources for further guidance. Avoid clearing the CMOS while the system is on; it will damage the mainboard. Click the audio icon from the window tray at the lower-right corner of the screen. Please apply some heat sink paste on top of your CPU to dissipate the heat more effectively.
S3-related functions described in this section are available only when motherboxrd BIOS supports S3 sleep mode. Be- fore inserting the power supply connector, always make sure that all compo- nents are installed properly to ensure that no damage will be caused. To use the USB 2. Also, it provides the instructions on con- necting the peripheral devices, such as the mouse, keyboard, etc.
Page 89 MS ATX Mainboard 4-Channel Mode for 4-Speaker Output The audio jacks on the back panel always provide 2-channel analog audio output function, motherboagd these audio jacks can be transformed to 4- or 6- channel analog audio jacks by selecting the corresponding multi-channel operation from No.
AGP is an interface specification designed for the throughput demands of 3D graphics. Hence, the program screens shown here in this appendix may be slightly different from the latest software utility and shall be held for reference only.
Sliding Pull the lever sideways away 90 degree Plate from the socket. You can clear CMOS by shorting pin while morherboard system is off.
Change these settings only if you are familiar with the chipset. Disabled, 2-Way and 4-Way. Technical Support Alternatively, please try the following help resources for further guidance. Most 10 Related.
MSI KT4A-V Instruction Manual
Page 88 Using 4- or 6-Channel Audio Function Connecting the Speakers When you have set the Multi-Channel Audio Function mode properly in the software utility, connect your speakers to the correct phonejacks in accordance with the setting in motherbosrd utility. Using 4- or 6-Channel Audio Function 3. Each category includes none, one or more setup items. User may try this combination, but MSI will not guarantee its functionality. The instructions shown on the Speaker Configuration screen may vary depending on how you motherhoard the options of No. Read the following steps to have the Multi-Channel Audio Function properly set in the software utility, and have your speakers correctly con- nected to the Back Panel. Full Screen Logo Show This item enables you to show the company logo on the bootup screen.
MSI KT4A-V User Manual